How To Flush Water Heater

How To Flush Water Heater

How To Flush Water Heater: We often do small or big tasks of our household, but when it is time flush water heater, we neglect it. Although this is a tedious task, but if you love hot water, then it is an important task to do. Is it necessary to do? Yes, it is an essential task because if you do not do this, the water heater will have gunk and minerals stored inside it, resulting in it not being operated efficiently and will not last very long.

How To Flush Water Heater

So if you want to save your money and make your water heater last longer, flush it at least once a year. Hot water is very beneficial for our body; it plays a useful role in relieving pain. Water heater takes care of us by producing hot water that’s why we also need to return it something. How can we? Flush it any one time of the year and remove all the dirt from it.

Now the question is how to flush water heater? You will be happy to know that this is an effortless task. Follow some steps, and you will get a positive result. We are here to give you a full idea of ​​how to flush a water heater. So read the entire article and flush your water heater yourself.


Step 1: Turn off Water Heater


Before starting any work, you must keep safety in mind as you will never want to face any danger while working. Before starting work, make sure your water heater is disconnected from the power source.

If it is electric, then you must unplug it. On the other hand, if it is gas then note the temp for it next time, and then turn the gas control knob to “Pilot”. So before proceeding, make sure your water heater is completely turned off. Once confirmed, you can start working.


Step 2: Test your Pressure Relief Valve


If you want to make your water flow faster and easier during draining, you can open the pressure relief valve. Although it is not a necessary step, it helps the water to flow easily during draining. It also allows you to test how well your pressure relief valve is fitted.

You need to make sure you have a bucket under the drainpipe opening your water before the pressure relief valve. This water will be so hot; if you see that the water is not coming out, then you should realize that you have got a faulty pressure relief valve and you must replace it.


Step 3: Connect Hose to Spigot


It is essential to make sure that the hose of the other end is out or at least in the bucket before turning on the spigot. If you think, the water heater is in the basement then use a portable pump so that you can pump water out of the basement and into the ground floor.


Step 4: Turn on Drain and Spigot


You should continue draining the tank until the water is appropriately sedimented free. If you notice that your tank still has a large amount of sediment, you will need to clean it properly.


Step 5: Flush the Water Heater


Re-open the cooling water valve at the top of your tank for a few seconds, then close it again and drain the water. It will light up any left sediment so you can fully flush your hot water heater. Try to repeat this process until you see no more sludge coming out of your tank.


Step 6: Refill the Tank


Turn off the drain valve and pressure relief valve and disconnect your hose. Now turn on all the hot water taps in your home. As you refill your tank, any pressure issues that flow freely will prevent your water line from rising.

Now turn the cooling water supply back on again and let your tank fill. When it is fully loaded, open the pressure relief valve one more time to release the excess air it contains and shut it down after a while. Now pay attention to the faucets, once the water flows back to a stable state, turn them off again.


Step 7: Turn on Power


Since your water heater was completely shut down before work, you need to restart it now. If the water heater is electric, plug it in again. On the other hand, if it is gas, then return to the knob to the temperature it was set before.

If you can follow the above steps, you can easily flush your water heater yourself without spending any cost.


Final Words:


As we mentioned earlier, flushing water heaters is an important task. You must flush it once a year, in order to make the water flow faster and last longer. Flushing is not a difficult task. You do not have to spend any money to hire an expert for this. If you can follow some steps well, you can do it yourself.

With all of you in mind, here are some steps on how to flush a water heater. Try to follow these steps well. We hope our small effort will help you a lot to get the best possible result.

User Review
5 (1 vote)