How To Install Dewalt Trimmer Line

How To Install Dewalt Trimmer Line

How To Install Dewalt Trimmer Line: If you have a trimmer or use it daily, it is often difficult for you to mount the thread. While this task should be straightforward, it can be difficult and stressful for people sometimes, mainly when different brands employ various methods of installation! Don’t worry; if you have a Dewalt trimmer, we’re here to help. We’re here to teach you how to mount a Dewalt trimmer and get you back to work in no time.

How To Install Dewalt Trimmer Line

Here we are going to know about how to install dewalt trimmer line.

Remove the trimmer head:

We must understand that removing the trimming head is the most complicated step of the whole program, so different procedures are needed for each model to remove the head. Fortunately, for all Dewalt trimmer models, you only have to use one tool. You may not need to cut the head before mounting the line except for specific 20V Dewalt versions.

Test the battery first to see whether or not it has power. If so, let the computer run until the battery is running out. Then remove the battery and downplay the unit. The trimmer and show knob can now be used. At this time, you have to unlock the trimmer head momentarily in a safe position.

Push the trimmer head down and turn it to the right. The indicator knob is also rotated to free it from the coil. The trimmer head is removed when the handle is out of the locked position, and you can remove the handle from the holder.

Note: You may damage the entire unit and the machine’s lock if you don’t pull out the head correctly. Make sure that you straight up take your back.

Fast load the winding line:

If the trimmer head is removed, continue to the next stage. You will have to spin the line with a fast load during this process. You have to search your brain first. If all is good, consider drawing streamers from one end to the other through these gaps. The lines should be about 2 or 3 feet deep. Drop the lines in the middle until you are finished.

And look at the head and see a symbol with an arrow. Place an open hand on the trimmer head and surround it with five fingers, turning into the arrow sign. Please turn it off, and the trim lines are 2 to 3 inches. After starting, switch on. If your head doesn’t get the line out, go back to Phase 2 and repeat it.

Place a traditional head:

Possibly only a dual-feed would occur if your Dewalt does not have a good loading head. You would need a tool called a flat head screwdriver to promote the load on this dual-feed unit. Before you begin spinning the thread, make sure the thread is at least 10 feet long.

All right, let’s begin with the lines far from the front of the head now. Look at the arrow in the trench and wave these trim lines in the path of these bows. Think of these lines along the trimmer chute winding beautifully and neatly. Alternatively, when the system is working, you may be trapped or find blocked. When you have completed the winding, you can position it between the two lines if there are more than 6 inches of a line left.

Note: Have you finished the step above? If so, with the second line, you can now use the same winding form. You should use a screwdriver to keep them straight if the lines do not avoid flowing out of the hole while winding.

Do line winding with the traditional head:

It is quite likely that you have a double feed if you don’t have a Dewalt with a fast-loading head. You will have to power this trimmer with a flat head screwdriver to make it smoother while the second compartment is filled.
Ensure you have two 10-foot lines and wind instead. First, look at the arrows in the trench and remind you in what direction you have to wind the line from the head’s top. The arrows are on the trench.

Keep the winding straight and organized around the trench, piling them in layers so that the trimmer is not obscured or knotted. You will now start winding the second line with about 6 centimeters of line left in the retaining groove in the two-line compartments’ center.


When you put trimmers on your Dewalt, one of the most challenging things to do is first to cut off your head. Please make sure you do so in a well-lit place, so you do not have to reach the trimmer near you, because this can lead to harm, particularly when you pull your head up and out of the block.

If you have anything to know more on this topic then let us know in the comments section below.

User Review
0 (0 votes)