How to Make a Crossbody Hobo Bag

How to Make a Crossbody Hobo Bag

Introduction: You wanted a bag that could carry much stuff and was hands-free, so you had it packed with whatever you want. So definitely you can use a crossbody hobo bag.

How to make a crossbody hobo bag

SO, let’s see and gather some knowledge about how to make a crossbody hobo bag.

Necessary materials:

This bag can be made out of two external bags and two linens in its simplistic form. Standard leather/vinyl cover, tie, and purse.  These are made of plastic, plastic, or vinyl. Whatever it may be. (Or some other wear-free fabric)

Even four shots are needed. Attach a zip pocket for a fully packed pack! For each wallet, you need a zipper and a button. I often include a belt, which includes a pin, two locks on the ends of the stripe, 2 D-ring strap lugs, and some hardware: two D-ring clasps and two swivel clasps.

Step 1:

Place the right-hand side of the outer bag and tie the wrong side of the bottom bag over the back to keep all sections together. To suit the inserts already removed from the outer pocket, remove inserts from the base cover. (Free to apply a sort of interface to the elements of your exterior or inner lining. I’d say that I lighten the design because vinyl has a good bottom structure, but in other words, you want the top of the bag to be a little flexible.

Step 2:

Remove the outer bag and work on the cover. You can directly o for step 8 if you don’t want to add pockets. The green lining will be added to the bottom pocket (left), so the “wallet matching” points will be labeled. A zip pocket is shown in the jacket on the right.

Step 3:

Place the top two corners of the pocket with the points on the furnace on the right. In either line, my bag’s lining looks the same. check the step 8 to push on the pocket with the marked rectangle and stitch the marked spot. Cut the rectangle down to and from each corner after stitching. Drawdown to the edges right away, don’t draw them.

(The example below shows the stitching on the opposite side of the cover, so it is a little easier to see from that side.)

Step 4:

Now it’s about time to pull the pocket into the hole you’ve just cut. (We are staring at my pocket cloth right now, after having pulled it out.) Pay attention to the top and sides of the opening of the envelope. They appear to sit in the wrong place. But it should remain in place as you click the pocket hole with the hammer.

Step 5:

Turn the filler up to the right. Place the zipper under the opening and close (right side up). I use buttons, but in other tutorials, you can use the glue stick process. Stitch the zipper inside. It would help if you considered not suturing your teeth while the zip is longer than the hole. I always stitch on the zipper teeth, raise my needle and drive foot, save the teeth again, lower the needle, and stitch again. Reduce zipper waste.

Step 6:

Break off the unused zip and tie the lower side to the top side. Place together the blunt edges of the bag. We ensure that you protect the pocket fabrics, not the lining of the sac. Sew with 1/2 “seam pertinent on the edges and also the high of the bag.

Step 7:

Bring together the two bits on the right. Sew with 1/2 “seam tolerance on the edges and bottom.

Step 8:

Pay full attention to the edges of the leather under trimming on the exterior of the case. You want to balance the two sides. Try to use loops on the leather/vinyl part instead of buttons.

  • If you can do follow the instruction what given above, then you can easily make a crossbody hobo bag for yourself.

Conclusion:

You may have noted that my external bag does not meet the lower end of the jacket. That’s because I use the outer pocket fabric from the pocket, and they haven’t been long enough. If you don’t understand that my outer bag looks distinctly from yours, I point this out. Move the leather/vinyl along with the pins, don’t forget!

5
Sending
User Review
0 (0 votes)